Saltar a contenido principalHaga clic para ver nuestra Declaración de accesibilidad o contáctenos si tiene preguntas relacionadas con la accesibilidad.

Configure Smart eSolutions on Systems Using an External or Integrated Fiery Controller

Artículo #: 9MrawLC0MG6zuh7j3f22v9 | Publicado: 19/01/2021

Productos compatibles
  • C60/C70 a color de Xerox®
  • Xerox Color EC70 Printer
  1. Configure the Fiery Controller for Smart eSolutions:
    1. Locate the IP Address of the Fiery from a Network Controller Configuration Page. See the Related Content for additional information.

      NOTE: If the IP Address is already known, skip to step C.(Open a Web Browser).

    2. Locate the Network Settings section of the configuration and take note of the IP Address.  On most networks, the required address will be the IPv4 address.
    3. Open a Web Browser and enter the IP Address of the Fiery into the Address field, and then press Enter.  The Fiery Webtools Page should now load. 
    4. Click on the Configure tab.
    5. Click Launch Configure.

      NOTE: If you receive the Java "Do you want to run this application" message, click Run.  If you receive a "Block potentially unsafe components from being run" message, click Don’t Block.

    6. Login as an administrator.  The default username is "Admin".

      IMPORTANT: The Fiery documentation may mention “Fiery.1” as the default password. Do not use this password when you log on to the Fiery server for the first time. Instead, print a Fiery Server Configuration page and look for ID in the BIOS Setup section (listed under RIP).  For a stand-alone Fiery server, the default password is listed in the ID field. For the integrated Fiery server, the default password is the first 14 alphanumeric characters listed in the ID field. 

      Note: If you reinstall the Fiery system software or restore factory default settings, the administrator password will be replaced by “Fiery.1”.  Use “Fiery.1” to log on to the Fiery server and then change the password to prevent unauthorized usage.

    7. Select Network, and then select IPv4 Address.
    8. If Configure IP Address is set to 'Manual', by the Configure DNS Server radio button, select the Manual radio button.
    9. Enter the DNS Primary Server address as per the users Network Administrator.
    10. Enter the DNS Secondary Server address as per the users Network Administrator.
    11. Enter the DNS Suffix if used. This may be the Domain Name. If you are not sure, contact your Network Administrator. 
    12. Click on Save.

      IMPORTANT: The next step will halt any print jobs being printed through the Fiery.

    13. Restart the Fiery when prompted.

  2. Configure CentreWare Internet Services for Smart eSolutions:
    1. After the Fiery has restarted, refresh the webpage by pressing F5 on the keyboard.
    2. After the Fiery Webtools page loads, locate and click on the Xerox CentreWare Internet Services link at the bottom, right corner of the page. CenterWare Internet Services will now load.

      NOTE: This link may also be called Xerox Color C60/C70 Printer, and the location may vary.

    3. From the menu at the top, select Properties.
    4. If prompted, log in as the administrator.

      Note: The default administrator user name is admin. Depending on when the device was manufactured or the software version installed, the default administrator password may be the device serial number or 1111. The user name and password are case sensitive.

    5. From the menu at the left, select SMart eSolutions Setup.
    6. If the Network has a Proxy Server, select Proxy Server.

      If the Proxy Server information is unknown, contact your System Administrator.

    7. Under Use Proxy Server, check the Enabled box.
    8. Under Server Name, enter the Hostname or the IP address of the Proxy Server.
    9. Under Port Number, enter in the Port number of the Proxy Server.
    10. Enter in a Login Name and Password if the Proxy Server requires authentication.
    11. Under HTTPS, repeat the same steps for Server Name, Port Number and if a Username/Password is used.
    12. Scroll to the bottom of the page and click Apply to save changes.
    13. Select Communication Status.
    14. Next to Communication Mode, select Configure.
    15. Next to SMart eSolutions Enablement, check the Enabled box.
    16. Click Apply.
    17. Return to the Communication Status screen.
    18. Next to Communication Mode, select Configure.
    19. Click Test XCDG Connection.  If the communication is successful, Smart eSolutions is now working from the Device side, If an error occurs, Contact Support for assistance.

Contenidos relacionados

¿Ayudó esto?