Access the Embedded Web Server as System Administrator

NOTE: The images in this procedure are for demonstration purposes only and may not specifically match your printer model; colors, icons, and other minor differences may exist.

You can access the administration and configuration settings from the Tools menu on the control panel or from the Properties tab in the Embedded Web Server. The control panel consists of a touch screen and buttons you press to control the functions available on the printer. The Embedded Web Server is the administration and configuration software installed on the printer. It allows you to configure and administer the printer from a Web browser.

The administrator password is required when accessing locked settings in the Embedded Web Server or at the control panel. Most printer models have a default configuration that restricts access to some settings. Access is restricted for settings on the Properties tab in the Embedded Web Server, and settings on the device touch screen Tools menu on the device touch screen.

NOTE: Xerox recommends the default password be modified from the default for security reasons. Refer to Change the System Administrator Password

Before you begin:

• Locate your device IP address using the Configuration Report. Refer to Print the Configuration Report.

• Ensure that TCP/IP and HTTP are enabled. If you disabled either of these protocols, enable them at the control panel before accessing the Embedded Web Server. Refer to Enable TCP/IP and Enable Hypertext Transfer Protocol (HTTP)

IMPORTANT: As the steps to perform certain tasks may vary depending on the Software Version, it may be important to determine the version of software that is currently installed on the device. Refer to How To Determine the Software (Firmware) Version Installed on the Device

Software Version 100.xxx.xxx.xxxxx: Access the Embedded Web Server as System Administrator: 

To access the Embedded Web Server

1. At your computer, open a Web browser. In the address field, type the IP address of the device, then press Enter or Return.
   
   
   
   

To log in to the Embedded Web Server as the administrator:

1. In the top right area of the page, click Login.
   
   
   
   

2. For User ID, type admin.

3. For Password, type the administrator password.
   
   NOTE: The default password is 1111.
   
   

4. Click Login.
   
   
   
   

To logout of System Administrator mode from the Embedded Web Server:

1. Click the Admin-Logout button in the upper right corner. The Logout screen displays.
   
   
   
   

2. Click the Logout button.
   
   
   
   

Software Version 101.xxx.xxx.xxxxx: Access the Embedded Web Server as System Administrator: 

To access certain features, tools, and apps, log in to the Embedded Web Server for your device.

Note:

• Access to some restricted functions requires administrator rights.

• Depending on the software version installed on the device, the default password may be the device serial number or 1111.  The password is case sensitive.  For software version 101.xxx.019.20200 or higher, the default password is the device serial number.

• If you have not changed the default administrator password, you are prompted to change the password when you login as administrator in the Embedded Web Server.

To log in to the Embedded Web Server:

1. 1. At your computer, open a Web browser. In the address field, type the IP address of the printer, then press Enter or Return.
      
      
      
      

To log in to the Embedded Web Server as the administrator:

1. In the top right area of the page, click Login.
   
   
   
   

2. For User ID, type admin.
   
   
   
   

3. For Password, type the administrator password.  The password is case-sensitive.  
   
   Note: Depending on the software version installed on the device, the default password may be the device serial number or 1111.  The password is case sensitive.  For software version 101.xxx.019.20200 or higher, the default password is the device serial number.    
   
   

4. If you are logging in for the first time, set up a password.

   1. Type the old password.

   2. Type a new password. To verify the password, retype it.
      
      Note: The new password must adhere to all minimum password requirements. For details, contact your system administrator.
      
      

   3. Click Save. The new password is stored.
      
      Note: When you attempt to log in with the default password, the system prompts you with this message: The default password for the admin account is still being used. For greater security, changing the default password is recommended.
      
      Select an option:

      • Prompt at Next Login: Select this button to leave the password at the default setting.

      • Change Password / Policy: Select this button to change the password.  Refer to Change the System Administrator Password

To logout of System Administrator mode from the Embedded Web Server

1. Click the Admin-Logout button in the upper right corner. The Logout screen displays.
   
   
   
   

2. Click the Logout button.